Front 20mm Hubs

[Rosscofat]

I need some sugestions on front disc hubs for a monster t or Slider.. under 300$

[Burnwood]

Front 20mm hubs are very hard to screw up. So buy the cheapest one you can find...

My Formula was $50...

[Rosscofat]

I can get a chris king one for 80$ but formula sounds cheep

[Kirill]

i run marz...
i love it, but if u get the slider, doesnt it use hex lock, and isnt that a diff system???

[C.C.]

Originally posted by Rosscofat
I can get a chris king one for 80$ but formula sounds cheep

CK new for $80? Hook me up! If you can get one for that price, get it!

Most QR 20 hubs are pretty reliable. Formula, Hayes make decent hubs. But for $80, get the CK for pimp factor.

[BAC5.2]

I have a Marz hub because it was cheap. I also use a slider. All 20mm thru axle hub's are the same.

I will be replacing it with a Chris King if it ever screws the pooch.

[Rosscofat]

does the hex use a diff? and yes 80$ from Rocky :D

[BAC5.2]

use a diff what?

No, all 20mm thru axle hubs are the same.

[Rosscofat]

good :)

[BAC5.2]

Damn, 80 bucks?

I can get a standard QR hub for $75, but the 20mm is $94 (shipped for both). My rear is only $154 though (204 with stainless steel driveshell and funbolt's :)).

[DangerousDean]

obviusly get the king, it will outlast the formulas and marz 100 times over, by the time the king is done, formula and marz wil be out of business or seomthing :eek:

[Rosscofat]

im getttin formula :D the CK is to high class for me

[mudshArk]

I believe the marz hub use a bearing with a larger od. that's good

[UFO]

teh marz hub should be just a relabelled formula. front hubs are pretty idiot proof, there really isnt much to go wrong. screw pimp factor, get the cheapest you can get

[IFO]

Originally posted by UFO
screw pimp factor, get the cheapest you can get

exactly... theres no point to a CK frt hub...

get a Formula.. it'll do teh job adn last a long time...

if u were refering to a rear hub that would be a different story...

[Shmoe]

Originally posted by UFO
teh marz hub should be just a relabelled formula. front hubs are pretty idiot proof, there really isnt much to go wrong. screw pimp factor, get the cheapest you can get

Its not, the marz hub uses larger bearings and is a little different inside.

[HEYPIP]

Originally posted by Burnwood
Front 20mm hubs are very hard to screw up. So buy the cheapest one you can find...

My Formula was $50...

formula, novatec and kt 20mm hubs are pretty good.
they're great and almost as good as a king if you put a good quality ball bearing in them. if you add the price of a taiwanese 20mm hub and new german bearings, it's less than a king.

ck hubs still rule.

pip

[switch]

Originally posted by IFO
exactly... theres no point to a CK frt hub...

get a Formula.. it'll do teh job adn last a long time...

For sure. I've had one for about 2.5 years, and the only work I've done on them is replace the bearings (after 1.5 years). That cost me $18.

[HEYPIP]

Originally posted by Count Blah
What's your opinion on rear hubs? Kings still leading the pack?

that depends on your criteria.

pip

[Rosscofat]

I see hubs as hubs I ran a 99 XTR rear hub for 4 years and it still runs smooth :) only reason I changed it was for disc brakes im goin formula